Carbon Steel SA210 High Frequency Resistance Welded Helical Finned U Bend Tube for Exhaust Pipe Heat Recovery
SA210 U Bend Exhaust Pipe
,18m U Bend Pipe
,SA210 Welded Steel Pipes
High-frequency resistance welded helical steel fin tubes engineered for efficient waste-heat recovery from boiler flue gas. The fin strip is continuously and spirally welded onto a polished bare tube, bonding tube and fins into a single integral unit through high-frequency resistance welding.
| Material | Carbon Steel, Alloy Steel, Heat Resistant Steel, Stainless Steel, etc. |
|---|---|
| Tube Details |
Tube OD: 19 mm min. Tube Length: 18 meters max. Fin Height: 32 mm max. Fin Thickness: 0.8 mm min. Fin Pitch: min. 4 mm for solid fins & 3.3 mm for serrated fins. |
| Production Capacity | Daily production capacity up to 40 tons. |
| HFW Fin Type | Solid plain and serrated. |
U-Bent Welded Spiral Evaporator Tube — SA210 Gr. C SMLS Carbon Steel Tube.
High-frequency resistance welded helical steel fin tubes are widely used in the recovery of waste heat from boiler flue gas. The fin strip is welded continuously and spirally wound onto a polished bare tube, with the tube and fins bonded together using high-frequency resistance welding technology.
All tubes are finished with an outside red-oxide zinc phosphate primer and an inside volatile corrosion inhibitor (VCI) in water-soluble tablet form. They are suited to a wide range of applications, including fired heaters, heat exchangers, boilers, economizers, pre-heaters, coolers, heat pipes, and heaters.
We produce both solid plain and serrated helical welded steel finned tubes. All spiral welded tubes can be bent in the middle or at the end of the finned section — these are known as hairpin tubes.
Inspection for un-welded fin sections, fin damage after finning, copper pollution, tears, wrap, and similar defects.
Verification of fin height, fin spacing, fin inclination, fin corrugation, and the length of finned and un-finned portions.
Assessment of ovality, thickness, and area reduction.
| Bevel | 30°–35° |
|---|---|
| Bevel Root Size | 0.5 mm – 1.5 mm |
| Delivery Condition | Tube ends are square cut, free of burrs, internally dried and air-blown clean, and externally coated with varnish at both ends of the helical welded tubes. |
Documentation includes QAP, WPS, PQR & WPQ, raw material mill certificates, inspection and test sample results, and the manufacturer's warranty certificate.
A wide range of fin and tube material combinations is available.
| Items | General Materials | Popular ASTM Materials |
|---|---|---|
| Core Tube Material | Carbon Steel, Alloy Steel, Heat Resistant Steel, Stainless Steel, etc. | 10#, 20#, 15CrMo, Cr5Mo, Cr9Mo, 1Cr18Ni9Ti, 0Cr18Ni9, 00Cr17Ni14Mo2, SA106B, SA106C, SA192, SA179, SA178, SA214, SA210-A1, SA210-C, TP304/304L/304H, TP409/410, TP316/316L, TP321/321L, TP347H, T11, T22, T91, etc.; SA210 Gr. C SMLS |
| Fins Material | Carbon Steel, Alloy Steel, Heat Resistant Steel, Stainless Steel, etc. | Q235-BF, 08F, 08AL, 1Cr18Ni9Ti, 0Cr13, 1Cr13, 0Cr18Ni9, 09CrCuSb, CS, A1008-B, SPHC, SPCC, TP304/304L, TP316/316L, TP321/321L, etc. |
| Solid Helical Steel Fin Tubes Fabrication Range | Solid Fins (mm) | Serrated Fins (mm) | ||
|---|---|---|---|---|
| Min | Max | Min | Max | |
| Tube OD (mm) | 19 | 219 | 19 | 219 |
| Fin Height (mm) | 8 | 26 | 8 | 32 |
| Fin Thickness (mm) | 0.8 | 2.8 | 1 | 1.6 |
| Fins Density (mm) | 4 (250 FPM) | 20 | 3.3 (303 FPM) | 20 |
| Tube Length (mm) | N/A | 18000 | N/A | 18000 |
- Tube swaging process for the joint of two tubes.
- Spacer rings (material: steel) are available.
- One side solid plain fins and the other serrated fins — two fin types on the same tube.
- More than 10,000 square meters of workshop, including 4 ERW high-frequency welding finning lines, with a daily production capacity of around 40 tons.
- Comprehensive quality assurance plan for high-frequency welding spiral steel tubes:
- Raw material control for both plain tubes and fins.
- In-process control with reports including WPS, PQR & WPQ; weld deposition efficiency testing before fabrication; non-destructive testing and tensile testing.
- Final inspection control with reports (visual and dimensional checks, etc.).
- The high-frequency resistance welded fin tube is integrally extended for maximum surface area to achieve efficiency. The heat transfer ratio of the high-frequency welded fin tube is approximately 8–9 times higher than that of plain tubes.
- This welded helical fin tube is a singular integral unit, eliminating heat contact resistance and losses. Generally, the tube-side temperature can reach up to 800°C for stainless steel fins; low carbon steels, withstanding up to 475°C, are the most common choice.
- Inquiry — professional quotation, or send us more details on the inquiry item.
- Confirm the price, lead time, payment terms, and other details.
- Proforma invoice sent by email or online.
- Make samples according to your request, send photos or samples, and arrange production.
- Send production line photos and confirm the estimated delivery time again.
- End of production — mass production product photos and samples are sent to you for approval.
- Inform you of the tracking number and check the status for clients.
- The order can be marked "finished" once you receive the goods and are satisfied with them.
- Provide feedback on quality, service, market feedback, and suggestions so we can do better.
TP304L Resistance Welded Perforated Fins Longitudinal Finned Tube for Heat Exchangers
DELLOK YONGHUI Cold Drawn Carbon Steel Fin Height 16.5mm Extruded Fin Tube
DELLOK YONGHUI Chemical Industry Stud SA335 P91 Carbon Steel Seamless Tube